{"id":4576,"date":"2013-08-15T09:27:33","date_gmt":"2013-08-15T13:27:33","guid":{"rendered":"http:\/\/fish-news.com\/cfn\/?p=4576"},"modified":"2015-03-06T12:54:03","modified_gmt":"2015-03-06T17:54:03","slug":"safe-boat-smart-boat-electrical-systems-batteries-cables-safety","status":"publish","type":"post","link":"https:\/\/fish-news.com\/cfn\/safe-boat-smart-boat-electrical-systems-batteries-cables-safety\/","title":{"rendered":"SAFE-BOAT SMART-BOAT: Electrical systems \u2013 Batteries, cables, safety"},"content":{"rendered":"

by Fred Mattera \u2013<\/strong><\/p>\n

Batteries are an integral power source on fishing vessels.\u00a0 They provide power to the vast majority of our pilothouse electronics and are a power source for alarms and startup and shutdown systems for main engines and gensets.<\/p>\n

Be sure to install batteries so they are capable of withstanding vessel roll, pitch, and vibration.\u00a0 Otherwise, the slightest motion could cause flexing and breakage of starter cables that could create a fire hazard or lead to a loss of power.<\/p>\n

\"A

A qualified Coast Guard-approved marine drill instructor, Fred Mattera of Point Judith, RI is the owner\/president of North East Safety Training Co. (NESTCo), which conducts fishing vessel drills and inspections and basic safety training workshops.
A commercial fisherman for 40 years, Mattera is a member of the Commercial Fishing Safety Advisory Committee to the Coast Guard, and, since 1998, has been president of the Point Club, a fishing vessel mutual insurance group. He also has served on the board of directors for Sunderland Marine Mutual Insurance Co., the principal underwriter for the Point Club and more than 2,000 US fishing vessels, since 1998.<\/p><\/div>\n

Lead acid batteries require lead drip trays, while alkaline batteries require steel drip trays.\u00a0 These trays should be capable of containing any electrolyte that may be spilled during charging or testing.\u00a0 Batteries should be installed so that they can be inclined 30\u00b0 without spilling electrolytes.<\/p>\n

Keep batteries clean and dry, protecting them from exposure to seawater or fresh water, and provide adequate ventilation to remove dangerous hydrogen gas released during charging.\u00a0 Remember, hydrogen is lighter than air and can accumulate in overhead pockets, creating an explosive hazard.\u00a0 Do not ignore this explosive hazard of batteries.\u00a0 Avoid sparks, flames, electrical switches, and smoking in the battery storage area.<\/p>\n

Provide ample room around batteries for ease of removal and access to terminals.\u00a0 Install box covers and\/or terminal covers on batteries.\u00a0 If a tool is dropped on an unprotected battery, the result can be arching, shorting-out, or explosion.<\/p>\n

All battery connections must be permanent.\u00a0 Don\u2019t use spring clamps or temporary connections.<\/p>\n

All vessels should have a back-up battery in the pilothouse with a small trickle charge to provide power to specific electronics such as radios, GPS, and radar for emergencies in case all power is lost.<\/p>\n

 <\/p>\n

Cables<\/b><\/p>\n

All cables and wires should have copper conductors of the appropriate size and voltage rating for the circuit.\u00a0 Stranded copper wire should be used aboard vessels because it is more flexible and less likely to fracture due to vibration or movement.<\/p>\n

Protect cable runs from the weather to the extent you can.\u00a0 PVC can be used as a conduit to protect cables and wires in areas exposed to weather.<\/p>\n

Cables and wires should be supported in a way that avoids chafing or other damage.\u00a0 Wire clips and brackets should be spaced proportionately to maintain straight runs because trouble usually starts at bends.\u00a0 Cables should enter fittings from the bottom so water can\u2019t run along the cable and fill the fittings.<\/p>\n

Protect cables in areas subject to mechanical abuse with metal coverings or heavy, thick rubber hoses.\u00a0 It\u2019s always a good idea to scan your wiring and look for areas of wear or chafing.\u00a0 Then replace or provide adequate chafing protection to avoid a fire hazard.<\/p>\n

Consider this:\u00a0 The number one cause of engine room fires is faulty or chafed wiring in electrical systems.<\/p>\n

Cable runs and fittings in fish holds, net lockers, and lazarettes should be watertight.\u00a0 Cables installed in refrigeration compartments must be suitable for low temperature and high humidity.<\/p>\n

Wherever possible, separate cables serving duplicated equipment so that a problem with one does not affect the other.\u00a0 Terminations and connections should be grounded properly and housed in fire retardant enclosures.\u00a0 Terminations, connections, and splices should be vibration resistant and accessible.\u00a0 Use watertight outlets, junction boxes, and caps where electrical components are exposed to weather.<\/p>\n

All electric motors must be provided with protection against overload such as breakers and motor starters.\u00a0 Lighting in engine rooms, sorting or packing areas, the fish hold, and deck should have two circuits so a failure of one doesn\u2019t leave the area without light.\u00a0 Lights in these areas should have impact globes or guards.<\/p>\n

It\u2019s important to position pilothouse electronics as far as possible from doors and windows to minimize corrosion.<\/p>\n

Make sure your vessel\u2019s electronics and electrical systems are serviced and maintained by certified, knowledgeable personnel.<\/p>\n

 <\/p>\n

Safety tips<\/b><\/p>\n

First and foremost, whenever doing electrical work be sure that all circuits involved have been de-energized and tag them to prevent anyone from accidentally re-energizing them.\u00a0 Some equipment or accessories may be energized by more than one circuit, so take care to ensure that all power has been disconnected.\u00a0 If you have any doubts, test the circuit with a voltmeter.<\/p>\n

If unusual circumstances make it impossible to de-energize the equipment, every care should be taken to insulate the person performing the work from grounded and energized parts.<\/p>\n

Everyone doing electrical work should take the following precautions:<\/p>\n